Microcontrollers, FPGAs, CPLDs and memory programmed at our Northampton facility with silicon-manufacturer-approved algorithms, verified device by device, and returned in tube, tray or on tape and reel ready for your line.
Submit your details to connect with our team.
Device programming is loading firmware or configuration data into a programmable chip, such as a microcontroller, FPGA, CPLD, EEPROM or Flash memory, before or after it is fitted to a circuit board. A programming service does this at volume on dedicated equipment, verifies every device against the master file and returns the parts ready for assembly.
Microchip PIC and AVR, NXP, STMicroelectronics and Renesas microcontrollers; Xilinx, Altera and Lattice FPGAs and CPLDs; EEPROM, Flash memory, PLDs and logic devices.
Through-hole DIP through to fine-pitch BGA, QFP, SOIC and LCC. If your part is not listed, send us the part number and we will confirm support.
Silicon-manufacturer-approved algorithms, a full read-back check of every device against the master, and firmware revision recorded against each reel.
Returned in tube or tray, or taped and reeled to EIA-481-D at your pitch and reel size, with Kapton or polyester labels or laser marking.
Same-day and next-day turnaround on most jobs, and 24/7 support when a production line has stopped.
Use us alongside your own programmers or main supplier when they are fully loaded, out of action or too slow for a build date.
Five steps from your master data to programmed devices on your line.
Send the part number, package, quantity and your master data by email, disc or master device.
We confirm the algorithm, checksum, security settings, labelling and the output format you need.
Devices are programmed on approved programmers under ESD-controlled handling.
Every device is read back and verified against the master, then labelled or laser marked as specified.
Parts are returned in tube, tray or on tape and reel, or held in secure stock, with batch traceability from receipt to despatch.
Which method a device needs affects turnaround, tooling cost and whether the part is best programmed before or after board assembly.
Devices are programmed in a socket or automated handler before they reach the assembly line, then taped and reeled ready for pick-and-place. It is the fastest route at volume, gives full electrical verification of every device and keeps programming off your production line. It is how the large majority of the devices we programme each year are handled.
Firmware is loaded after the device has been soldered to the board. It suits late-stage configuration, parts that cannot be socketed and builds where firmware is finalised after assembly. It is slower per unit than socket programming and needs a programming header designed into the board.
The device is programmed in place over a small number of pins while it stays connected to the surrounding circuit. It is common for field updates, engineering builds and low-volume runs.
JTAG (IEEE 1149.1) and SWD (Serial Wire Debug, the two-pin ARM interface) are debug interfaces that also carry programming data. They are the usual choice for ARM Cortex parts, FPGAs and CPLDs. Where a device supports both, SWD saves pins and JTAG gives wider chain and boundary-scan capability.
Not sure which applies? Send the part number and target volume and we will tell you which route we would use and why.
Most manufacturers use one or more of three routes. This is how they compare in practice.
| In-house programming station | Distributor programming | Specialist programming service | |
|---|---|---|---|
| Best for | Engineering builds, small batches and firmware that is still changing | Buying and programming parts in one order | Consigned parts, mixed manufacturers, volume and urgent work |
| Device coverage | Limited to the programmers, adapters and sockets you own | Usually limited to the parts the distributor sells | Broad coverage across manufacturers and packages |
| Turnaround | Immediate when equipment and an operator are free | Depends on the distributor's programming queue and location | Same-day and next-day on most jobs with us, 24/7 for line stops |
| Output | Loose parts unless you also tape and reel in-house | Usually on tape and reel | Tube, tray or tape and reel, with marking and dry packing |
| Watch out for | Equipment downtime, operator time, and verification and traceability falling on your team | Being tied to one distributor's stock | You supply the parts and master data |
Programming, labelling and tape and reel in one place, so programmed devices arrive ready to place and programming does not hold up a build.
Keep us on file alongside your current arrangement. Start with a first job, check it against your own acceptance criteria, then use us for overflow, equipment downtime and emergencies.
Every device is programmed on site at our facility in Northampton, England, so the only transit is the delivery to your line. Customers in Europe can see delivery and customs details on our European page.
Without full read-back verification, failures surface at test or in the field. Every device we programme is verified before it is reeled.
Without device-level traceability, a firmware error becomes a whole-batch problem. We record the revision against each reel, so any recall stays contained.
Lock bits, secure boot and encrypted programming need setting at programming time and confirming afterwards. We handle file security, checksums and chain of custody as standard.
Devices handled outside controlled conditions can pass verification and fail later. Programming runs under ESD control, with dry packing for moisture-sensitive parts where the MSL requires it.
If parts come from the open market, counterfeit screening can run before programming so you are not programming suspect devices.
Programming, taping and reeling, laser marking and dry packing run under one job number, so there is one supplier and one set of records.
Everything on one site, from one UK supplier.
Short answers to what buyers usually ask first.
Loading firmware or configuration data into a programmable chip such as a microcontroller, FPGA, CPLD, EEPROM or Flash memory. A programming service does this at volume, verifies every device against the master file and returns the parts ready for assembly.
Microcontrollers from manufacturers including Microchip, NXP, STMicroelectronics and Renesas, FPGAs and CPLDs from Xilinx, Altera and Lattice, and EEPROM, Flash memory, PLDs and logic devices, in packages from DIP to fine-pitch BGA. Send the part number if yours is not listed.
Same-day and next-day on most programming jobs, with 24/7 support for line-stop situations. Send your device, quantity and deadline and we will confirm what is possible.
The part number and manufacturer, package, quantity, your programming file or master device, any security settings, the labelling you need and the output format, plus your deadline.
Yes. We programme the devices and return them taped and reeled to EIA-481-D at your exact pitch and reel specification, ready for direct placement on your SMT line.
No. Many customers use us for overflow and emergency work alongside their own programmers or an existing supplier.
Yes. Devices are programmed in Northampton and shipped to customers across the UK and Europe. See our European page for delivery, customs and paperwork.
Not currently. Our quality system is certified to ISO 9001:2015 (UKAS accredited) and we are working towards AS9100 Rev D, ITAR compliance and JOSCAR accreditation.
Send the part number, package, quantity and your programming file and we will confirm turnaround and a quote. Line stopped? Call 01604 491107.
Converting, programming, testing, and packaging electronic components for defence, aerospace, automotive, and medical manufacturers since 1992.
Tel: (01604) 491107
info@systemationeuro.com
Systemation Euro Automotive Ltd
19 Mansion Close
Moulton Park Industrial Estate
Northampton
NN3 6RU
England